Will the excavated area be a minimum of 6” (150mm) wider than the actual pave area?
Yes, when the aggregate base is placed in the excavated area, the extra width will help ensure stability of the base at the edges, and provide space for the required edge restraints.
How will the contractor grade the paver installation for drainage?
By sloping the paved area away from the house at a minimum of 2%.
Will the aggregate base absorb or hold water?
No, when compacted properly, its density will minimize deformation and/or heaving of the paved surface during freezing or thawing.
Will the base be aggregate, ranging in size from approximately ¾” (20mm) to sand?
Yes, this facilitates compaction to a required density while allowing proper water drainage.
How will the aggregate base be compacted?
The base should be compacted in 4” (200mm) layers to achieve the maximum density and load bearing capacity. Each layer will require several passes of a compactor to achieve this.
Will the bedding sand be loosely screeded to a depth of 1” (25mm), but no thicker than 1½” (40mm) thick?
Yes, the loosely placed, even layer of washed coarse sand provides a setting bed for the pavers. When the pavers are placed on the sand and compacted, the sand moves up into the joints. This causes the pavers to interlock and become level after compaction. Note: limestone screenings and stone dust should not be used for bedding sand.
How will the contractor assure an even color mix of the pavers?
By taking pavers from several bundles or pallets at a time.
Will an edge restraint be installed?
Yes, an edge restraint around the perimeter of the pavers is essential for eliminating horizontal creeping of the pavers and loss of bedding sand. There are a wide variety of edge restraints. They may be installed individually as manufactured segments or cast in place at the project site. Manufactured Edge Restraints: · Plastic edging · Aluminum or steel edging · Partial depth precast concrete edging · Precast concrete of cut stone · Cast in Place Edge Restraints · Poured-n-place concrete curbs · Troweled concrete.
Are the joints filled between the pavers?
Yes, with clean, fine sand. The sand should be dry sand so it will flow freely into the joints. The pavers are compacted during and after filling to begin interlock of the units and prevent sand from washing from the joints.
Should there be inspection of the pavers after their compaction?
Yes, the owner and the contractor should inspect the pavement together and confirm the owner’s satisfaction.
Yes, when the aggregate base is placed in the excavated area, the extra width will help ensure stability of the base at the edges, and provide space for the required edge restraints.
How will the contractor grade the paver installation for drainage?
By sloping the paved area away from the house at a minimum of 2%.
Will the aggregate base absorb or hold water?
No, when compacted properly, its density will minimize deformation and/or heaving of the paved surface during freezing or thawing.
Will the base be aggregate, ranging in size from approximately ¾” (20mm) to sand?
Yes, this facilitates compaction to a required density while allowing proper water drainage.
How will the aggregate base be compacted?
The base should be compacted in 4” (200mm) layers to achieve the maximum density and load bearing capacity. Each layer will require several passes of a compactor to achieve this.
Will the bedding sand be loosely screeded to a depth of 1” (25mm), but no thicker than 1½” (40mm) thick?
Yes, the loosely placed, even layer of washed coarse sand provides a setting bed for the pavers. When the pavers are placed on the sand and compacted, the sand moves up into the joints. This causes the pavers to interlock and become level after compaction. Note: limestone screenings and stone dust should not be used for bedding sand.
How will the contractor assure an even color mix of the pavers?
By taking pavers from several bundles or pallets at a time.
Will an edge restraint be installed?
Yes, an edge restraint around the perimeter of the pavers is essential for eliminating horizontal creeping of the pavers and loss of bedding sand. There are a wide variety of edge restraints. They may be installed individually as manufactured segments or cast in place at the project site. Manufactured Edge Restraints: · Plastic edging · Aluminum or steel edging · Partial depth precast concrete edging · Precast concrete of cut stone · Cast in Place Edge Restraints · Poured-n-place concrete curbs · Troweled concrete.
Are the joints filled between the pavers?
Yes, with clean, fine sand. The sand should be dry sand so it will flow freely into the joints. The pavers are compacted during and after filling to begin interlock of the units and prevent sand from washing from the joints.
Should there be inspection of the pavers after their compaction?
Yes, the owner and the contractor should inspect the pavement together and confirm the owner’s satisfaction.
No comments:
Post a Comment